Frequently Asked Questions
The founders of GH IA met recently to answer the questions they are most often asked about their company and heating technology.
Questions About Induction Heating
How hot does the induction coil get?
STEVE: "The induction coil is cool to the touch; the heat that builds up in the coil is constantly cooled with circulating water."
Can you use induction heating to braze steel parts in a nitrogen atmosphere?
DALE: "Yes you can, but the nitrogen has to be clean and have a low dew point."
Can diamond bits be brazed with induction heating?
DALE: "Sure, in fact induction heating is preferable for diamonds bits because it works so quickly. The longer the diamond remains at heating temperature, the faster it degrades. We recommend atmospheric brazing in a vacuum atmosphere for the best results."
How do I select a braze alloy?
STEVE: "We've put together a Brazing Alloy Selection Guide to help you choose the best option. It depends on the composition of your part, how and where it will be used, and the joint strength required. Another helpful service we provide for our customers is to put them in touch with an experienced braze alloy supplier."
We've been running these old vacuum furnaces for years. How can we set up a leaner operation?
STEVE: "The best thing you can do is unplug those old furnaces and invest in a quick, clean vacuum induction system. Our new compact induction vacuum furnace will fit right into your manufacturing cell."
When is it better to use the indirect heat of an induction furnace instead of direct induction heat?
DALE: "Yeah, we get that question a lot. It depends on the geometry of your part and how you want to heat it. If you have a part with simple geometry and your process calls for heating a specific area of the part, direct induction heating will generally be preferable. However, if you need to heat the entire part, or if the part has a complex shape, then you'll achieve better results with an induction heating vacuum furnace."
Will induction heating increase my utility bills?
STEVE: "Not likely. Induction heating is a very effective, efficient means of heating. Most of our customers who are switching to induction for the first time see their utility bills go down." EXAMPLE
What are typical utility requirements for induction?
STEVE: "Of course it depends on the system, but a typical typical system requires 440, 3-phase VAC at 60 Hz and 30 Amps. Also figure on 80 PSI compressed air and 40 PSI water at 4 gallons per minute for cooling."
Can you braze glass or ceramics with induction?
DALE: "If you work with glass or ceramics, a compact vacuum furnace is a great solution for brazing. You'll get quick, clean heat with very precise temperature control."
Is this joint suitable for induction brazing?
STEVE: "Our team of metallurgical and mechanical engineers will be glad to have a look at your parts and process and give you our best advice - no obligation! MORE
Can induction be used to nickel braze in nitrogen?
DALE: "Yes, with a vacuum system. We've had some success in with foil preforms, but we've had no luck with nickel paste because the binder in the paste doesn't flow. So we suggest using a high vacuum system because it will work faster than oven heating and there is no time for nitrides to form." VACUUM SYSTEM
I am using an induction system to heat a graphite object under a nitrogen atmosphere with pressure of about 100 microns. I am seeing a glow around the coil. This does not seem normal, and the current draw seems high. Can you explain why this is happening?
DALE: "100 micron is right in the middle of the range where the dielectric strength goes to zero, so you are operating at the worst possible pressure / vacuum. Here's a chart to help you out. MORE
Questions About GH IA
How long does it take to build a system?
STEVE: "We can build our standard systems, like our VF-10 Vacuum Furnace or our Bell Jar Heating Systems, in ten weeks. Custom-designed systems currently have a 16-week lead time."
Where is your largest installed base?
STEVE: "We sell systems worldwide and our largest installed base is currently in Singapore." CUSTOMERS
Do you install the systems you sell?
STEVE: "Absolutely. Every system quote includes installation, operator training, crating and shipping. All we ask is that you uncrate the system and move it into position before our service engineer arrives."
Can you handle small part runs in your lab?
DALE: "If you only need a small number of parts processed, we can help with that. Our lab equipment for our day shift becomes production equipment for our night shift." BRAZING SERVICES
How long have you been in business?
STEVE: "Our company was incorporated in 2002, but our core engineering team has been working together and building turnkey systems since 1998."
Do you have in-house manufacturing capability?
DALE: "With our in-house machine shop, we have full control over most of the manufacturing process. We purchase the electrical and vacuum system components, but basically we build the rest of the system right here." COMPANY PROFILE
What PLCs do you use in your systems?
DALE: "We'll work with whatever our customers need. Our engineers have experience with Allen Bradley, GE Fanuc, Modicon, Automation Direct, Xycom, Omron and more."
Why wouldn't it be less expensive for us to build the system in-house?
DALE: "When you talk about building your system in-house, consider the hidden costs: the inefficiency of designing and building something for the first time (the time and money lost to the learning curve); the cost of the machine tools and specialty equipment necessary to create the custom pieces; the lost floor space and disruption of normal factory flow during the assembly process; and supporting the system after it is up and running. And don't forget the time of all the personnel involved in the project engineers, technicians, machinists, electricians, purchasing agents, all the executives involved in the approval process. We have a great deal of experience building these systems and can deliver your system with guaranteed performance in the promised time frame."
Innovative Induction Heating